Get help your way
How do I find my Model Number?
Do you have the original packaging?
-
If your product came in plastic packaging (a clamshell), you’ll find the model number on the front of the insert card, on the lower left corner. If your product came in a box, you’ll find the model number on the top of the box.
Most model numbers are 12-16 characters and start with a couple letters followed by a dash.

No packaging? No problem!
-
The product number is on a label on the side of the dimmer or switch.*
If you’ve already installed the dimmer/switch, turn off the electricity and then remove the wallplate. Unscrew and remove the wallplate adapter, then unscrew the dimmer/switch and pull it out of the wall until you can see the label.
*Please note: The product number for Ariadni/Toggler dimmers is not on a label. It’s located directly on the front of the dimmer on the top left, or right below the on/off toggle.

- Browse Components
-
Applied Filter: Wall Controls > QSWS2-* > QSWS2-3BRLIRN
If you don't know your model number, try browsing for it here
- DALI 2 Digital LED Driver
- Hi-lume Driver EcoSystem
- Hi-lume Eco/3-Wire Driver
- Hi-lume Premier
- Hi-lume Premier EcoSystem
- Wireless Node
DALI 2 Digital LED DriverHi-lume Driver EcoSystemHi-lume Eco/3-Wire DriverHi-lume PremierHi-lume Premier EcoSystemWireless Node- A/V Control
- Automated Demand Response Kit
- Contact Closure
- Emergency Lighting
- Wallbox Contact Closure
A/V ControlAutomated Demand Response KitContact ClosureEmergency LightingWallbox Contact Closure- 0-10V ESN
- 0-10V Module
- ALPD-*
- DALI Universal ESN
- DALI Universal Module
- DMX Control Interface
- EcoSystem ESN
- EcoSystem Module
- Phase Adaptive ESN
- Phase Adaptive Module
- Switching ESN
- Switching Module
- T-Series ESN
0-10V ESN0-10V ModuleALPD-*DALI Universal ESNDALI Universal ModuleDMX Control InterfaceEcoSystem ESNEcoSystem ModulePhase Adaptive ESNPhase Adaptive ModuleSwitching ESNSwitching ModuleT-Series ESN- 3-wire Fluorescent
- EcoSystem to 0-10V
- EcoSystem to 3-Wire
- EcoSystem to Switching
- Fixture Mountable Ballast Module
- Phase Adaptive 3-Wire Fluorescent
- Phase-Adaptive
- Switching
- Ten Volt Interface
3-wire FluorescentEcoSystem to 0-10VEcoSystem to 3-WireEcoSystem to SwitchingFixture Mountable Ballast ModulePhase Adaptive 3-Wire FluorescentPhase-AdaptiveSwitchingTen Volt Interface10-Output Shade Power PanelIndividual ShadeQS Link- Athena Wireless Processor
- DIN Rail Processor
- Legacy Panel Interface
- Light Management Hub
- QS Sensor Module
Athena Wireless ProcessorDIN Rail ProcessorLegacy Panel InterfaceLight Management HubQS Sensor Module- Architrave
- Keyswitch
- Palladiom
- Pico Wired
- Pico Wireless
- QSWS2-*
- Signature Series
- Sunnata
- Sunnata Hybrid
- Sunnata Local Controls
- Touchscreen
ArchitraveKeyswitchPalladiomPico WiredPico WirelessQSWS2-*Signature SeriesSunnataSunnata HybridSunnata Local ControlsTouchscreenCeiling OccupancyDaylightDaylight Control PackageHigh Bay OccupancyPartitionWall OccupancyRadio Powr Savr CeilingRadio Powr Savr DaylightRadio Powr Savr Wall -
Athena


-
What is the model for replacement button kits?
You can change out any button kit on a seeTouch QS keypad to change the functionality. Below is a list of the different button kits. Please note you will have to change the keypad in the programming to�calibrate the keypad�to the new button configuration: this is done by holding the top and bottom buttons down for 25-30 seconds. Once all status LEDs begin flashing, release and again press the top and bottom buttons for another 5 seconds. Once the status LEDs discontinue from flashing, they keypad has been changed over.
QSWS2R-1BI - 1-button faceplate kit (Insert Style)
QSWS2R-1BIN- 1-button faceplate kit (Non-Insert Style)
QSWS2R-2BI - 2-button faceplate kit (Insert Style)
QSWS2R-2BN - 2-button faceplate kit (Non-Insert Style)
QSWS2R-3BI - 3-button faceplate kit (Insert Style)
QSWS2R-3BN - 3-button faceplate kit (Non-Insert Style)
QSWS2R-5BI - 5-button faceplate kit (Insert Style)
QSWS2R-5BN - 5-button faceplate kit (Non-Insert Style)
QSWS2R-7BI - 7-button faceplate kit (Insert Style)
QSWS2R-7BN - 7-button faceplate kit (Non-Insert Style)
QSWS2R-2BRLI - 2-button faceplate kit w/ raise/lower (Insert Style)
QSWS2R-2BRLN - 2-button faceplate kit w/ raise/lower (Non-Insert Style)
QSWS2R-3BRLI - 3-button faceplate kit w/ raise/lower (Insert Style)
QSWS2R-3BRLN - 3-button faceplate kit w/ raise/lower (Non-Insert Style)
QSWS2R-5BRLI - 5-button faceplate kit w/ raise/lower (Insert Style)
QSWS2R-5BRLN - 5-button faceplate kit w/ raise/lower (Non-Insert Style)
QSWS2R-1RLDI - 3-button and 2-button�faceplate kit w/ raise/lower (Insert Style)
QSWS2R-1RLDN - 3-button and 2-button�faceplate kit w/ raise/lower (Non-Insert Style)
QSWS2R-2RLDI - Dual 2-button faceplate kit w/ raise/lower (Insert Style)
QSWS2R-2RLDN - Dual 2-button faceplate kit w/ raise/lower (Non-Insert Style)
QSWS2R-3BDI - Dual 3-button faceplate kit (Insert Style)
QSWS2R-3BDN - Dual 3-button faceplate kit (Non-Insert Style)
QSWS2R-2BRLIRI - 2-button faceplate kit with IR receiver and raise/lower (Insert Style)
QSWS2R-2BRLIRN - 2-button faceplate kit with IR receiver and raise/lower (Non-Insert Style)
QSWS2R-3BRLIRI - 3-button faceplate kit with IR receiver and raise/lower (Insert Style)
QSWS2R-3BRLIRN - 3-button faceplate kit with IR receiver and raise/lower (Non-Insert Style)
QSWS2R-5BRLIRI - 5-button faceplate kit with IR receiver and raise/lower (Insert Style)
QSWS2R-5BRLIRN - 5-button faceplate kit with IR receiver and raise/lower (Non-Insert Style)



Athena Software
How do I find my Model Number?
Do you have the original packaging?
-
If your product came in plastic packaging (a clamshell), you’ll find the model number on the front of the insert card, on the lower left corner. If your product came in a box, you’ll find the model number on the top of the box.
Most model numbers are 12-16 characters and start with a couple letters followed by a dash.

No packaging? No problem!
-
The product number is on a label on the side of the dimmer or switch.*
If you’ve already installed the dimmer/switch, turn off the electricity and then remove the wallplate. Unscrew and remove the wallplate adapter, then unscrew the dimmer/switch and pull it out of the wall until you can see the label.
*Please note: The product number for Ariadni/Toggler dimmers is not on a label. It’s located directly on the front of the dimmer on the top left, or right below the on/off toggle.
