Get help your way
How do I find my Model Number?
Do you have the original packaging?
-
If your product came in plastic packaging (a clamshell), you’ll find the model number on the front of the insert card, on the lower left corner. If your product came in a box, you’ll find the model number on the top of the box.
Most model numbers are 12-16 characters and start with a couple letters followed by a dash.
No packaging? No problem!
-
The product number is on a label on the side of the dimmer or switch.*
If you’ve already installed the dimmer/switch, turn off the electricity and then remove the wallplate. Unscrew and remove the wallplate adapter, then unscrew the dimmer/switch and pull it out of the wall until you can see the label.
*Please note: The product number for Ariadni/Toggler dimmers is not on a label. It’s located directly on the front of the dimmer on the top left, or right below the on/off toggle.
- Browse Components
-
Applied Filter: Wall Controls
If you don't know your model number, try browsing for it here
- DALI 2 Digital LED Driver
- Hi-lume Driver EcoSystem
- Hi-lume Eco/3-Wire Driver
- Hi-lume Premier
- Hi-lume Premier EcoSystem
- Wireless Node
DALI 2 Digital LED DriverHi-lume Driver EcoSystemHi-lume Eco/3-Wire DriverHi-lume PremierHi-lume Premier EcoSystemWireless Node- A/V Control
- Automated Demand Response Kit
- Contact Closure
- Emergency Lighting
- Wallbox Contact Closure
A/V ControlAutomated Demand Response KitContact ClosureEmergency LightingWallbox Contact Closure- 0-10V ESN
- 0-10V Module
- ALPD-*
- DALI Universal ESN
- DALI Universal Module
- DMX Control Interface
- EcoSystem ESN
- EcoSystem Module
- Phase Adaptive ESN
- Phase Adaptive Module
- Switching ESN
- Switching Module
- T-Series ESN
0-10V ESN0-10V ModuleALPD-*DALI Universal ESNDALI Universal ModuleDMX Control InterfaceEcoSystem ESNEcoSystem ModulePhase Adaptive ESNPhase Adaptive ModuleSwitching ESNSwitching ModuleT-Series ESN- 3-wire Fluorescent
- EcoSystem to 0-10V
- EcoSystem to 3-Wire
- EcoSystem to Switching
- Fixture Mountable Ballast Module
- Phase Adaptive 3-Wire Fluorescent
- Phase-Adaptive
- Switching
- Ten Volt Interface
3-wire FluorescentEcoSystem to 0-10VEcoSystem to 3-WireEcoSystem to SwitchingFixture Mountable Ballast ModulePhase Adaptive 3-Wire FluorescentPhase-AdaptiveSwitchingTen Volt Interface10-Output Shade Power PanelIndividual ShadeQS Link- Athena Wireless Processor
- DIN Rail Processor
- Legacy Panel Interface
- Light Management Hub
- QS Sensor Module
Athena Wireless ProcessorDIN Rail ProcessorLegacy Panel InterfaceLight Management HubQS Sensor Module- Architrave
- Keyswitch
- Palladiom
- Pico Wired
- Pico Wireless
- QSWS2-*
- Signature Series
- Sunnata
- Sunnata Hybrid
- Sunnata Local Controls
- Touchscreen
ArchitraveKeyswitchPalladiomPico WiredPico WirelessQSWS2-*Signature SeriesSunnataSunnata HybridSunnata Local ControlsTouchscreenCeiling OccupancyDaylightDaylight Control PackageHigh Bay OccupancyPartitionWall OccupancyRadio Powr Savr CeilingRadio Powr Savr DaylightRadio Powr Savr Wall -
Athena
-
Athena System Installation Guide
-
Athena Touchscreen
-
LUT-Q-OPNADR-CPN8064
-
Lutron Residential and Commercial Systems Rules
-
Palladiom Button Kit (2-button, 3-button, 3-button with raise/lower, 4-button)
-
Palladiom Keypad Base Unit
-
Pico Wireless Control - 2-Button/3-Button
-
QS Keyswitch
-
seeTouch QS Glass Faceplate
-
seeTouch QS Glass Faceplate (non-Insert Style)
-
Signature Series QS
-
Square Palladiom Keypad
-
Sunnata RF Keypad Button Kit - Installation Guide
Athena Software
How do I find my Model Number?
Do you have the original packaging?
-
If your product came in plastic packaging (a clamshell), you’ll find the model number on the front of the insert card, on the lower left corner. If your product came in a box, you’ll find the model number on the top of the box.
Most model numbers are 12-16 characters and start with a couple letters followed by a dash.
No packaging? No problem!
-
The product number is on a label on the side of the dimmer or switch.*
If you’ve already installed the dimmer/switch, turn off the electricity and then remove the wallplate. Unscrew and remove the wallplate adapter, then unscrew the dimmer/switch and pull it out of the wall until you can see the label.
*Please note: The product number for Ariadni/Toggler dimmers is not on a label. It’s located directly on the front of the dimmer on the top left, or right below the on/off toggle.
