Caséta Support

APPLICATION	WIRING DIAGRAM	WALK ME THROUGH INSTALL	INSTALLATION VIDEO
1 Location (Single Pole)
2 Locations (3-Way) with a mechanical switch.
2 Locations (3-Way) with Pico Remotes*
2 Locations (3-Way) with Claro smart accessory switch (Model DVRF-AS)*
3 or more Locations (4-Way) with Pico Remotes*
3 or more Locations (4-Way) with Claro smart accessory switch (Model DVRF-AS)*

*Pico Remotes & Claro smart accessory switches sold separately.
 

Section (3): Product Settings

Adjusting the Low-End or High-End Trim
Trim settings can be used to set maximum (high-end) and minimum (low-end) available light levels from your dimmers. High-end trim settings can be used to save energy. Low-end Trim settings can be used to adjust your lights for the best performance. Please see steps to do so below.

NOTE: The DVRF-6L dimmer is the only dimmer that the Lutron App can be used to adjust the trim in the Caseta System. 

Step 1
Tap on the Diva Smart Dimmer from the Devices area in the Lutron App. Then select "Edit Device".



Step 2
Tap on "Trim".



Step 3
Adjust Trim levels you wish to change. Then select "Test & Save". Repeat as needed.



Status LED Indicator Light
Has a white soft glow status LED to indicate load status. As you move the slider up or down to set the dimming range the LED status light will move with the slider. If the lights are adjusted from a Pico remote, Lutron App, or third party voice integration, the LED status will follow that of where the command was sent from, meaning there could be times where the LED indicator status light does not match the slider. If the dimmer is then turned off and then turned on manually from the dimmer it will turn on to the level where the slider is physically set. When the slider is moved the LED status will immediately move with the slider. For example: Slider on dimmer is set to 50% and then a Pico remote is pressed to turn on to 100%. The LED light will track to the top of the dimmer. If you were to then move the slider manually at the dimmer the LED status light would follow the position of the slider as well as the lights the dimmer is controlling.

Note:
The LED Indicator light can only be disabled/enabled with the use of the Lutron App. Please see the steps to do so below.

Step 1
Tap on the Diva Smart Dimmer from the Devices area in the Lutron App. Then select "Edit Device".



Step 2
Tap on the "Status LED".



Step 3
Select "On" or "Off" (default is On) and then tap on "Save" in the top right corner of the screen.




The ADVANCED INSTALLATION GUIDE  will guide you through several additional installation topics beyond what was covered in this article.

Section (4): Troubleshooting
 

Symptoms	Probable cause and action
Light does not turn on or in-wall dimmer light bar does not light up.	• Light bulb(s) burned out. • Breaker is OFF or tripped. • Light not properly installed. • Wiring error. • FASS switch on the dimmer is in the Off position.
Light does not respond to Pico remote control.	• The dimmer failed to pair with Pico remote control; see Pairing the dimmer and Pico remote control. • The dimmer is already at the light level the Pico remote control is sending. • The Pico remote control is outside the 30 ft (9 m) operating range. • The Pico remote control battery is low. • The Pico remote control battery is installed incorrectly
• Bulbs turn off while being dimmed. • Bulbs turn on at high light level but do not turn on at a low light level. • Bulbs flicker or flash when dimmed to a low light level.	Verify bulbs are marked dimmable and visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance.